+ Reply to Thread
Page 11 of 11 FirstFirst ... 7 8 9 10 11
Results 301 to 314 of 314
  1. #301
    SUPER COMMANDO
    Join Date
    Sep 2014
    Location
    Florida

    Re: ZX10/14 Stick Coil PnP Harness - Interest -

    I'm new member of the cool kids club . Arash showed a photo of his stick coils with the upper dust boot from the OE wires fitted to them . I liked the look and did the same to mine . The harness and coils work Great ! Name:  stick coils.jpg
Views: 171
Size:  328.5 KB Down here in Water World I thought it 's a good idea to limit the ability of water to collect and puddle on top of the spark plug tube area .
    [Wiseco 1109 kit 12:1/6 speed trans/CNC ported head/Muzzy X3 cams/Tsugiki pipe/Ladybird can/ZX11 ignition/ELS+2 ignition rotor/CVK 40 carbs/BEAR Racing Velocity Stacks/stock CVK36 springs/192 keihin mains/FP K87 TI needles/3rd clip/42 pilots/pilot screws 3 turns out/float level 14mm/K&N pod air filters/Billet Thug Fork Yokes/ZX10 front end/ZX10 wheels/1200 swing arm/Ohlins HO 417 rear shocks/Greg Couch 2 piece sprocket cover/ZX9 gauges/Speedhut GPS Gauge 180mph/ThrottleMasters ]

  2. #302
    BadAss Hooligan
    Join Date
    Mar 2011
    Location
    Savannah, GA

    Re: ZX10/14 Stick Coil PnP Harness - Interest -

    Howard,

    It is not DRASTICALLY different, but changed the following:

    - New higher grade, higher temp wire (Also smaller OD, but same gauge of copper)
    - More coverage of heat shrink for additional protection.
    - Change to assembly process of the terminals.
    - Change to assembly process of heat shrink.
    - Added individual heat shrink support to the 4 terminal connector.

    Let me know if it is satisfactory.

    Cory
    '99 ZRX (Green) #8998
    '76 KZ900
    '08 Concours 1400

  3. #303
    BadAss Hooligan
    Join Date
    Oct 2009
    Location
    Palmer Lake, CO

    Re: ZX10/14 Stick Coil PnP Harness - Interest -

    I am sure it's going to be fine, the things that you saw in the harness are being addressed and it was a rare instance.

    Thanks again Cory.
    01 GREEN, ZX9 gauges,Sonic 1.1 springs,DMR shocks,Holeshot Touring bars,MCL 1 risers,Buell pegs,Couch fork brace and rear brake torque link,JE 12.5:1 stock bore,ZZR cams,double springs,CVK40's,BEAR RACING CVK40 velocity stacks,dual foam uni-pods,Keihin 150 mains,#40s@2.0 turns,FH 15mm, FP K87 TI needles, 3.0 clip position,plastic slides,FP ZX11 springs,Muzzy 4-2-1/Ti oval can,stock ZRX ECU/+2 Ted's rotor, NGK CR10EIX plugs,ZX14 stick coils,Ted's pod tray,4-pot calipers.

  4. #304
    BadAss Hooligan
    Join Date
    Mar 2011
    Location
    Savannah, GA

    Re: ZX10/14 Stick Coil PnP Harness - Interest -

    Quote Originally Posted by BonzRexster View Post
    I am sure it's going to be fine, the things that you saw in the harness are being addressed and it was a rare instance.

    Thanks again Cory.
    Well if you want something changed, let me know. Someone has asked me for a same harness with Techflex brading over the heat shrink. Mostly for appearance, as it works great for abrasion resistance, but not heat.

    Cory
    '99 ZRX (Green) #8998
    '76 KZ900
    '08 Concours 1400

  5. #305
    BadAss Hooligan
    Join Date
    Oct 2009
    Location
    Palmer Lake, CO

    Re: ZX10/14 Stick Coil PnP Harness - Interest -

    Like you said, it was an isolated incident. I am grateful for what you did! Top notch attention to detail in what you do based on the tweaks you listed.

    Happy to see the new orders coming in with this thread being read more these past weeks.

    Thanks again!
    01 GREEN, ZX9 gauges,Sonic 1.1 springs,DMR shocks,Holeshot Touring bars,MCL 1 risers,Buell pegs,Couch fork brace and rear brake torque link,JE 12.5:1 stock bore,ZZR cams,double springs,CVK40's,BEAR RACING CVK40 velocity stacks,dual foam uni-pods,Keihin 150 mains,#40s@2.0 turns,FH 15mm, FP K87 TI needles, 3.0 clip position,plastic slides,FP ZX11 springs,Muzzy 4-2-1/Ti oval can,stock ZRX ECU/+2 Ted's rotor, NGK CR10EIX plugs,ZX14 stick coils,Ted's pod tray,4-pot calipers.

  6. #306
    BadAss Hooligan
    Join Date
    Oct 2009
    Location
    Palmer Lake, CO

    Re: ZX10/14 Stick Coil PnP Harness - Interest -

    Thank you Cory, new harness looks good!

    Name:  IMG_20190405_160122.jpg
Views: 143
Size:  2.19 MBName:  IMG_20190405_160148.jpg
Views: 143
Size:  1.52 MBName:  IMG_20190405_160131.jpg
Views: 142
Size:  2.18 MBName:  IMG_20190405_160157.jpg
Views: 143
Size:  3.23 MB
    01 GREEN, ZX9 gauges,Sonic 1.1 springs,DMR shocks,Holeshot Touring bars,MCL 1 risers,Buell pegs,Couch fork brace and rear brake torque link,JE 12.5:1 stock bore,ZZR cams,double springs,CVK40's,BEAR RACING CVK40 velocity stacks,dual foam uni-pods,Keihin 150 mains,#40s@2.0 turns,FH 15mm, FP K87 TI needles, 3.0 clip position,plastic slides,FP ZX11 springs,Muzzy 4-2-1/Ti oval can,stock ZRX ECU/+2 Ted's rotor, NGK CR10EIX plugs,ZX14 stick coils,Ted's pod tray,4-pot calipers.

  7. #307
    Hooligan
    Join Date
    Apr 2009
    Location
    Australia

    Re: ZX10/14 Stick Coil PnP Harness - Interest -

    Can I add myself to the list for one of these sent to Australia please?
    Last edited by Nelso; 04-17-2019 at 11:22 AM.
    http://www.zrxoa.org/forums/signaturepics/sigpic26544_3.gif

  8. #308
    BadAss Hooligan
    Join Date
    Mar 2011
    Location
    Savannah, GA

    Re: ZX10/14 Stick Coil PnP Harness - Interest -

    Quote Originally Posted by Nelso View Post
    Can I add myself to the list for one of these sent to Australia please?
    Nelso,

    Please see here: http://www.zrxoa.org/forums/showthre...ad-amp-Respond

    Cory
    '99 ZRX (Green) #8998
    '76 KZ900
    '08 Concours 1400

  9. #309
    Stuffed Up
    Join Date
    Nov 2015
    Location
    Brisbane QLD, Australia

    Re: ZX10/14 Stick Coil PnP Harness - Interest -

    So I am getting around to ordering the rest of what I need to install this now and question around what to buy?

    I know in the 1st post there is a summary of what will work - but I was more interested in if there is any RECOMMENDED one to buy? Do any work/fit better etc?
    Or are they all same/sam - so just look for the best deal on any of the ones listed???
    #10079

    2007 - Ixil SlipOn Exhaust, BW Headers, NoFlo's, Uni Pods, +4 ELS Advancer, FP Jetting

  10. #310
    BadAss Hooligan
    Join Date
    Aug 2001
    Location
    Christmas, FL

    Re: ZX10/14 Stick Coil PnP Harness - Interest -

    Quote Originally Posted by Diggs View Post
    So I am getting around to ordering the rest of what I need to install this now and question around what to buy?

    I know in the 1st post there is a summary of what will work - but I was more interested in if there is any RECOMMENDED one to buy? Do any work/fit better etc?
    Or are they all same/sam - so just look for the best deal on any of the ones listed???
    If you are asking about the stick coil choice ??, hands down from my experience since 2008, the most available(at least here) and easiest to fit are the CBR600RR. Just flip upper seal and lightly coat outside with silicone grease, done.


    Honda CBR600RR 04-15 (only), oem p/n 30700-MEE-641, new cost ??
    Denso p/n 129700-4510 res. 1.5/1.6 ohms x 2 = 2.9 ohms

    Orig. owner, 99 ZRX, 61k+
    ZX11cams,pistons
    Stick coils, DIM Harness
    Cam degree 105 int.,107 exh.
    Fact. 1.0 w/Ti.,108 MJ
    Airbox w/ K+N
    Full Akro
    OEM ign. +5 Adv
    Dyno 131.7 HP/80.4 TQ.
    Ohlins RS, Race tech fork
    Fork brace+Steering damper




    "TO BOLDLY GO WHERE NO MAN HAS GONE BEFORE" IS EASY, RETURNING IS THE REAL CHALLENGE.

    " WHEN YOU OWN A CHINESE SCOOTER, ALL CHINESE SPARE PARTS ARE OEM QUALITY "

  11. #311
    Stuffed Up
    Join Date
    Nov 2015
    Location
    Brisbane QLD, Australia

    Re: ZX10/14 Stick Coil PnP Harness - Interest -

    Yup, that's exactly what I was after Allen! Cheers for that
    #10079

    2007 - Ixil SlipOn Exhaust, BW Headers, NoFlo's, Uni Pods, +4 ELS Advancer, FP Jetting

  12. #312
    BadAss Hooligan
    Join Date
    Oct 2009
    Location
    Palmer Lake, CO

    Re: ZX10/14 Stick Coil PnP Harness - Interest -

    Any model year ZX-14 or C14 as well, at least as of last year.
    01 GREEN, ZX9 gauges,Sonic 1.1 springs,DMR shocks,Holeshot Touring bars,MCL 1 risers,Buell pegs,Couch fork brace and rear brake torque link,JE 12.5:1 stock bore,ZZR cams,double springs,CVK40's,BEAR RACING CVK40 velocity stacks,dual foam uni-pods,Keihin 150 mains,#40s@2.0 turns,FH 15mm, FP K87 TI needles, 3.0 clip position,plastic slides,FP ZX11 springs,Muzzy 4-2-1/Ti oval can,stock ZRX ECU/+2 Ted's rotor, NGK CR10EIX plugs,ZX14 stick coils,Ted's pod tray,4-pot calipers.

  13. #313
    BadAss Hooligan
    Join Date
    Mar 2011
    Location
    Savannah, GA

    Re: ZX10/14 Stick Coil PnP Harness - Interest -

    I have the ZX10 mitsu.#F6T549/560 coils and they fit very well in the factory ignition wells in the valve cover. They have three ribs at the top and ramp into the well taper. I use a little dielectric grease on the ribs so that when it comes to removing they come out easier.

    Cory
    '99 ZRX (Green) #8998
    '76 KZ900
    '08 Concours 1400

  14. #314
    Stuffed Up
    Join Date
    Nov 2015
    Location
    Brisbane QLD, Australia

    Re: ZX10/14 Stick Coil PnP Harness - Interest -

    Thank you all - managed to find some ZX14 items locally for a decent price!
    #10079

    2007 - Ixil SlipOn Exhaust, BW Headers, NoFlo's, Uni Pods, +4 ELS Advancer, FP Jetting


 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Powered by vBulletin® Version 4.1.7
Copyright © 2019 vBulletin Solutions, Inc. All rights reserved.
All times are GMT -4. The time now is 09:39 AM.
vBulletin 4.0 skin by CompleteVB