Search:

Type: Posts; User: MagicMan

Page 1 of 12 1 2 3 4

Search: Search took 0.13 seconds.

  1. Replies
    29
    Views
    668

    Re: Advice Needed, Galfer Front Brake Lines

    Nice!:thumbs:

    Where did you find the grommet?
  2. Replies
    29
    Views
    668

    Re: Advice Needed, Galfer Front Brake Lines

    :confused:

    Not sure of what you meant by getting the top and bottom lined up?

    Plus I am about to use Kwick's new badass bleeder.:thumbs:
  3. Replies
    16
    Views
    487

    Re: "BANNED" People

    I was Banned once,...^p
  4. Replies
    16
    Views
    449

    Re: My new ZRX was dropped off this week.

    Nice:thumbs:

    I think I saw some side covers on ebay the otherday.
  5. Replies
    29
    Views
    668

    Re: Advice Needed, Galfer Front Brake Lines

    I bought the set from Kwick, I had seen the set with the manifold that does that.

    He had a sell on them awhile ago for a complete set including the clutchline, the packages say they are for the...
  6. Replies
    29
    Views
    668

    Re: Advice Needed, Galfer Front Brake Lines

    :LawnBoy,

    I thought there was a guy that was making those around here,...:stpoke:

    Where would it mount?

    This is what I have so far, I had to play around with it to make sure that the lines...
  7. Replies
    29
    Views
    668

    Re: Advice Needed, Galfer Front Brake Lines

    :LawnBoy

    Here's my plan, use these two mounting bolts,...

    312890312891


    With this hardware,...

    312892
  8. Replies
    34
    Views
    719

    Re: ZRX1200 Red for $1000

    The tail in the ad and the one that zarex posted.
  9. Thread: The devil

    by MagicMan
    Replies
    13
    Views
    335

    Re: The devil

    :howard:
  10. Replies
    34
    Views
    719

    Re: ZRX1200 Red for $1000

    Stripes don't match.^p
  11. Replies
    38
    Views
    781

    Re: Master and Slave Rebuild

    Well this was a $55 lesson:doh

    I went to Rocket Seals today and talked with the guy there, I had shown him what I had done and to my surprise he did not think it was compromised:LawnBoy Personally...
  12. Replies
    38
    Views
    781

    Re: Master and Slave Rebuild

    :doh

    Thanks:thumbs:
  13. Replies
    38
    Views
    781

    Re: Master and Slave Rebuild

    I just spoke with a rep from a local company Rocket Seals, I sent him the same pic that I have posted. He said that the part is actually a piston cup and that the rubber has to be rated to handle dot...
  14. Replies
    7
    Views
    282

    Re: Free if you can use it.

    Sounds like a ZRX mod party is in the works:LawnBoy
  15. Replies
    38
    Views
    781

    Re: Master and Slave Rebuild

    It did cross my mind to try the screw on method, I was worried about tearing it that way but ironically I tore it by using my o ring pic:brick:

    Lesson learned, I was going to buy new plugs for the...
  16. Replies
    38
    Views
    781

    Re: Master and Slave Rebuild

    :doh

    Right, it sucks that MamaKaw does not sell the O ring by itself. I should have just force rolled it over that "lip" instead I used my o ring pick.:brick:

    It looks like the o rings are the...
  17. Replies
    38
    Views
    781

    Re: Master and Slave Rebuild

    :brick:

    Well looks like I tore my piston "o" ring a little bit trying to fit it over the clutch master piston!!

    Just a tiny tear on the inside section of it, it is hard to get a pic of it:cry:...
  18. Replies
    38
    Views
    781

    Re: Master and Slave Rebuild

    I ordered the parts from KWICK, it was less than $240 there are three kits I bought for the clutch brake and rear brake. Plus new diaphrams, dust boots for the masters and a new seal for the slave I...
  19. Replies
    38
    Views
    781

    Re: Master and Slave Rebuild

    None of which had been done until I got the bike, just like the valve adjusting and carb sync:doh

    This is the first time that the masters have been torn down, I rebuilt the calipers when I first...
  20. Replies
    38
    Views
    781

    Re: Master and Slave Rebuild

    No, I wish I had a setup like that.:LawnBoy

    Brake Cleaner, shop rags, green scotch brite(if needed), elbow grease and my air compressor then a microfiber rag to wipe down before I put the new...
  21. Replies
    38
    Views
    781

    Re: Master and Slave Rebuild

    :doh

    Those would work perfectly:thumbs:
  22. Replies
    38
    Views
    781

    Re: Master and Slave Rebuild

    Yeah, I have that Harbor Freight special, the damn head was to big to fit into the area which is why I bought those other snap ring pliers.:doh
  23. Replies
    22
    Views
    337

    Re: P & R Thread: No. 3 in a Series

    :rotflmao
  24. Replies
    38
    Views
    781

    Re: Master and Slave Rebuild

    :beer:

    Thanks Fellas, I just got everything disassembled and cleaned the clutch master housing.

    That damn snap ring was a bit of a pain in the ass to get out:doh

    312773312774312775

    ...
  25. Replies
    38
    Views
    781

    Re: Master and Slave Rebuild

    Thank you Sir:bd:

    :doh

    Time to start on this bad boy,...

    312769

    I plan on also repainting it, might as well:dunno
Results 1 to 25 of 300
Page 1 of 12 1 2 3 4
Powered by vBulletin® Version 4.1.7
Copyright © 2019 vBulletin Solutions, Inc. All rights reserved.
All times are GMT -4. The time now is 02:48 PM.
vBulletin 4.0 skin by CompleteVB