Search:

Type: Posts; User: NakedFun

Page 1 of 12 1 2 3 4

Search: Search took 0.39 seconds.

  1. Re: ZX11D CDI Plug and Play Harness - Round #2 - Interest

    Replied to your email. Yes they are still available, but traveling for work now, so it would be about 1 week out before I could ship (end of this coming week).

    Cory
  2. Re: All Those Looking For a Harness - NakedFun - Please Read & Respond

    Hi Chris,

    Sent you a PM. I have been traveling for work a bit the past few weeks, so I havenít been participating on here lately.

    Cory
  3. Replies
    6
    Views
    341

    Re: Spoked wheels search

    The ones I made for my bike probable ended up costing around that or more. So, it pays to find what you want......

    Cory
  4. Replies
    321
    Views
    56,620

    Re: ZX10/14 Stick Coil PnP Harness - Interest -

    All,

    I have been out for a while. Yes I still make these but to order. They are $45 shipped in CONUS paid via Paypal.

    Cory
  5. Replies
    67
    Views
    2,184

    Re: ZRX Topics of Discussion

    All you have to do is ride a C14 for a week and when you jump back on the ZRX it will feel like 250 MX bike.....

    Simple weight savings....

    Cory
  6. Replies
    26
    Views
    936

    View Post

    Any generic ďclickerĒ solenoid pump should work just fine.

    Cory
  7. Thread: Pontiac?

    by NakedFun
    Replies
    51
    Views
    1,890

    Re: Pontiac?

    Had a 2006 G6 GTP with the one year optional F40 6-Speed manual transmission. Car was fantastic for the 7 years I owned it.

    Iíll just leave this here......
    ...
  8. Replies
    321
    Views
    56,620

    Re: ZX10/14 Stick Coil PnP Harness - Interest -

    I have the ZX10 mitsu.#F6T549/560 coils and they fit very well in the factory ignition wells in the valve cover. They have three ribs at the top and ramp into the well taper. I use a little...
  9. Replies
    26
    Views
    936

    View Post

    Oh inside? Like a remote start panel? Or literally on the front side of the generator itself?

    Cory
  10. Replies
    26
    Views
    936

    View Post

    Iíll check to see what I can do when I get to work. I assume the panel you are talking about is the main control panel where to stop/start switch is?

    Cory
  11. Replies
    26
    Views
    936

    View Post

    6.5 Marquis? Can you tell me what part you are looking for? I might have a possibility of finding it for you?

    Cory
  12. Thread: New Vette

    by NakedFun
    Replies
    51
    Views
    2,199

    Re: New Vette

    I am not so sure the LT5 was correctly labeled as a ďClusterFxxxĒ. I also do not support that the VRod engine was in that same category. LT5 was and still is a fantastic engine. The price tag for...
  13. Replies
    18
    Views
    933

    Re: Steel Dragon Performance Velocity Stacks

    Why is the contact via email not enough?

    http://www.steeldragonperformance.com/

    I have purchased numerous items from them and they have always been responsive. They are the ones I worked with...
  14. Replies
    26
    Views
    936

    View Post

    I have always wanted to do something like that, bus conversion, RV rehab, etc... should be fun given the $$$ in reserve to not stall the project.

    Cory
  15. Replies
    9
    Views
    247

    Re: New Shoes For The Truck.....

    Yeah with everything, about 6 to 8 hours start to finish. Due to the Georgia heat and sun, had to buy the worlds largest pop up shelter to put him under.

    Cory
  16. Replies
    9
    Views
    247

    Re: New Shoes For The Truck.....

    Nope, unfortunately ďDukeĒ stays outside, but gets clay baríd and waxed regularly.

    Cory
  17. Replies
    9
    Views
    247

    Re: New Shoes For The Truck.....

    Yes. You give them your trucks specifications (suspension mods, make, model, year, etc...) and they somehow determine the appropriate offset. They also recommend a tire size. Went from a 215/85R16...
  18. Replies
    9
    Views
    247

    New Shoes For The Truck.....

    After 15 weeks of waiting for these one-off custom wheels my tires finally came in. So time for mount and balance. One concern was the fronts, and it turns out those concerns were valid. The...
  19. Thread: New Vette

    by NakedFun
    Replies
    51
    Views
    2,199

    Re: New Vette

    So evidently a used Ferrari 458 cost $60k.....

    Cory
  20. Thread: New Vette

    by NakedFun
    Replies
    51
    Views
    2,199

    Re: New Vette

    Some good info here: https://www.autoblog.com/2019/07/18/chevy-corvette-c8-reveal/

    - As stated, NO Manual trans, DCT auto.
    - Engine is a variant of the current C7 LT1 engine as a dry sump.

    In...
  21. Replies
    425
    Views
    9,430

    Re: AV80R in TN - July 1-15 2019

    Congrats Arash on the test! Your skills are always top notch!

    I survived Perky last night and his dogs....after they got a couple of bites in....

    His wife is spectacular BTW, donít know what...
  22. Re: First $100,000 mass production pick up truck in the pipeline

    That is because it uses the same options as the F350. Same 6.7L diesel and trans, but agreed that you crest the $100k once the nut tickler option is out fitted.

    Cory
  23. Re: First $100,000 mass production pick up truck in the pipeline

    Technically, they are right as I assume they are talking 1 Ton and smaller. 2018/2019 Ford officially added the F450 to its pickup line and crested the $100k with a F450 Platinum first......
    ...
  24. Green ZRX Sighting HWY 25E North Outside of Morristown, TB

    Was with a pack of various 70ís, 80ís, and 90ís Japanese bikes. Anyone here?

    Cory
  25. Re: All Those Looking For a Harness - NakedFun - Please Read & Respond

    BG,

    PM replied to. Will order parts and when I get back into town (8th) will build and ship directly.

    Cory
Results 1 to 25 of 300
Page 1 of 12 1 2 3 4
Powered by vBulletin® Version 4.1.7
Copyright © 2019 vBulletin Solutions, Inc. All rights reserved.
All times are GMT -4. The time now is 01:51 AM.
vBulletin 4.0 skin by CompleteVB