Search:

Type: Posts; User: KWICK

Page 1 of 12 1 2 3 4

Search: Search took 1.87 seconds.

  1. Replies
    35
    Views
    888

    Re: Chirp on deceleration?

    whatever, it takes a couple minutes to be sure. You should hear Harry Ellen’s header.
  2. Replies
    35
    Views
    888

    Re: Chirp on deceleration?

    Tap on the stock header with a rubber mallet.
  3. Replies
    35
    Views
    888

    Re: Chirp on deceleration?

    Alternator and header can be causes, see above
  4. Replies
    35
    Views
    888

    Re: Chirp on deceleration?

    Stock exhaust header?
    If so, the baffle weld(s) can crack internally and make a racket.

    Also, the alternator:
    http://www.zrxoa.org/forums/showthread.php?294056-Alternator-Loose-Bolt
  5. Re: AV80R starts making scrap metal - Taig Micro Lathe

    :thumbs:

    www.MSCDirect.com has every blade. I have a Lennox BiMetal one on mine.
  6. Re: AV80R starts making scrap metal - Taig Micro Lathe

    <iframe width="1280" height="512" src="https://www.youtube.com/embed/JvRAVCxb8y0" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture"...
  7. Replies
    35
    Views
    888

    Re: Chirp on deceleration?

    Measurement tells you nothing.

    As the cork gets out it absorbs oil and actually gets thicker.

    Does it slip?
    Is it grabby?
    If not, do t worry about it.

    Rebuild the slave cylinder with a...
  8. Re: AV80R starts making scrap metal - Taig Micro Lathe

    Yup, that is why the lathe Arash bought was a good deal, it came with GOBS of tooling. :thumbs:
  9. Re: AV80R starts making scrap metal - Taig Micro Lathe

    Squares are rectangles with OCD.
  10. Re: AV80R starts making scrap metal - Taig Micro Lathe

    DRO on the cross slide:

    <iframe width="1280" height="512" src="https://www.youtube.com/embed/f5Cg4C0e8Sw" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope;...
  11. Re: AV80R starts making scrap metal - Taig Micro Lathe

    I'll be making these, prototype on an old toolpost:

    320815
  12. Replies
    1
    Views
    129

    Wayne Rainey Rides Again!!

    This'll bring a tear to your eye...

    <iframe width="806" height="453" src="https://www.youtube.com/embed/imqwHIjwO2w" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope;...
  13. Re: AV80R starts making scrap metal - Taig Micro Lathe

    Too small Ewe say??

    Adapt and overcome!

    <iframe width="806" height="453" src="https://www.youtube.com/embed/J77plhVsX1A" frameborder="0" allow="accelerometer; autoplay; encrypted-media;...
  14. Re: AV80R starts making scrap metal - Taig Micro Lathe

    I do finished products everyday.

    www.ExpensiveLightweightShit.com
  15. Re: AV80R starts making scrap metal - Taig Micro Lathe

    Here ya go, Titanium. October 28th, 2017

    https://youtu.be/F4YjQwmiQQU
  16. Re: AV80R starts making scrap metal - Taig Micro Lathe

    Yeah, start with Titanium. :uptosum:

    Brass/bronze/copper is easy peasy.

    The first piece on my lathe was Titanium. And the second piece I tig welded was Ti.
  17. Re: AV80R starts making scrap metal - Taig Micro Lathe

    He does not know what it is yet. Wrong answers only.
  18. Re: AV80R starts making scrap metal - Taig Micro Lathe

    Insert EVIL laugh...

    320682
  19. Re: AV80R starts making scrap metal - Taig Micro Lathe

    <iframe width="806" height="453" src="https://www.youtube.com/embed/BPbR3uovtf8" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture"...
  20. Replies
    47
    Views
    1,251

    Re: Carbon Fuel tank build

    A friend of mine makes the KTM check valve the factory uses in it's tank vent hoses.
  21. Replies
    47
    Views
    1,251

    Re: Carbon Fuel tank build

    Yup, I published the 10 pound weight probably 18 years ago. The ZRX tank is light.
    You have your work cut out for you.
    I know it will be beautiful!

    Subscribed. ^p
  22. Replies
    10
    Views
    330

    Re: Is there a source for printed parts manuals?

    Kawasaki makes parts “books” available to everyone on their website and every parts house does also.
  23. Replies
    35
    Views
    888

    Re: Chirp on deceleration?

    Mouse caught in the fan shroud?
    It is winter....
  24. Thread: Jessi Combs

    by KWICK
    Replies
    16
    Views
    479

    Jessi Combs

    https://www.popularmechanics.com/cars/a29699776/jessi-combs-crash-cause-of-death/?source=nl&utm_source=nl_pop&utm_medium=email&date=110519&utm_campaign=nl18529660&src=nl
  25. Replies
    14
    Views
    481

    Re: Served with an "Evasion Offence Notice"

    This is Roscoe P Coltrain...we lost him Boss!
    ...
Results 1 to 25 of 300
Page 1 of 12 1 2 3 4
Powered by vBulletin® Version 4.1.7
Copyright © 2019 vBulletin Solutions, Inc. All rights reserved.
All times are GMT -4. The time now is 08:46 PM.
vBulletin 4.0 skin by CompleteVB